1. Welcome to Proudnaira.com the largest business forum in Nigeria; to enjoy the goodies of this forum you must Login or Register using the Login/Register button above.
    Dismiss Notice

The Use Of Coconut Fibre As Standard Ph Enhancer For Drilling Mud Formulation

Discussion in 'General Business' started by ResearchWap, Aug 26, 2019.

Share This Page

  1. ResearchWap

    ResearchWap New Member

    THE USE OF COCONUT FIBRE AS STANDARD pH ENHANCER FOR DRILLING MUD FORMULATION





    CHAPTER ONE

    BACKGROUND OF STUDY

    1.0 Introduction

    A drilling fluid, or mud is any fluid that is used in a drilling operation in which that fluid is circulated or pumped from the surface, down the drill string, through the bit, and back to the surface via the annulus.(Growcock et al., 2005).The successful and cost of a drilling process is known to depend extensively on the asset of the drilling fluid used (Gray et al., 1980). Drilling mud circulates in a loop, from the platform, where it is forced down into the formation by entering the drill string, and pushed up to the surface again via the drill bit. The fluid characteristics such as density and temperature are variables that need to be regularly monitored for perfect drilling conditions of the well (Issham et al. 1985). They provide primary well control of subsurface pressures by a combination of density and any additional pressure acting on the fluid column (annular or surface imposed). They are most often circulated down the drill string, out the bit and back up the annulus to the surface so that drill cuttings are removed from the wellbore. Drilling fluids have a number of alternative names, acronyms and slang terms used within the industry. The most widely used name is “mud” or “drilling mud” and both these terms will be used interchangeably throughout this chapter. Other drilling fluid names and acronyms are: water-based mud (WBM), oil-based mud (OBM), synthetic-based mud (SBM), non-aqueous fluid (NAF), invert emulsion fluid (IEF), high performance water-based mud (HPWBM), drill-in fluid (DIF) and reservoir drilling fluid (RDF). Similar to drilling fluids are so-called completion fluids that are used to finish the well after drilling is completed. The fluids used during completions are often referred to as work over and completion (WOC) fluids, clear brines and/or packer fluids. Drilling fluid is a major factor in the success of the drilling program and deserves careful study.

    [​IMG]

    Figure 1.0: Drilling fluids stored in the mud tank under agitation.


    The performance of the drilling fluid is critical to everyone involved with the operation and to all aspects of the drilling operation. The drilling fluid is the primary means to keep the well from blowing out and it is responsible for keeping the hole in good condition such that drilling operations can continue to the desired depth. Drilling and completion fluids are one of the most important parts of the well construction process and ultimately the performance of the fluid will determine the success or failure of the operation. The responsibility of the proper selection and application of fluid is held jointly between the fluids supplier, the drilling contractor and the operator.


    The research work focused on the use of Nigeria local materials in enhancing the drilling mud pH, its performance and contribution as drilling fluid properties and ensuring quality in hole making. Drilling fluid pH measurements and pH adjustments are fundamental to drilling fluid control because clay interactions, solubility of additives, and contaminant removal are all pH-dependent.

    PH is a value representing the hydrogen ion concentration in liquid and it is used to indicate acidity or alkalinity of drilling mud. The pH is presented in a numerical value (0 – 14), which means an inverse measurement of hydrogen concentration in the fluid.

    The pH formula is listed below;


    pH = - log 10 [H]


    Where: H is the hydrogen ion concentration in mol.


    According to the pH formula, the more hydrogen atoms present, the more acidity of substance is but the pH value decreases. Generally speaking, a pH of 7 means neutral. Fluids with a pH above 7 are considered as being alkaline. On the other hand, the fluids with pH below 7 are defined as being acidic.

    In the drilling mud, there are three main chemical components involved in Alkalinity of drilling fluid, which are bicarbonate ions (HCO3--), hydroxyl ions (OH --), and carbonate ions (CO3-2). The Alkalinity means ions that will reduce the acidity.

    In order to get accurate measurements for the pH, using a pH meter instead of using a pH a paper is recommended because it will give more accurate pH figures. Additionally, pH meters must be calibrated frequently.

    CLICK HERE FOR THE COMPLETE THESIS - THE USE OF COCONUT FIBRE AS STANDARD pH ENHANCER FOR DRILLING MUD FORMULATION

    THE USE OF COCONUT FIBRE AS STANDARD pH ENHANCER FOR DRILLING MUD FORMULATION - https://researchwap.com/oil-and-gas...ancer-for-drilling-mud-formulation/index.html
     

Share This Page

  1. ResearchWap
  2. ResearchWap
  3. ResearchWap
  4. ResearchWap
  5. ResearchWap
  6. ResearchWap
  7. ResearchWap
  8. ResearchWap